PreviousRunPlanDaily

This was for the PREX-I run in 2010. Run plans for PREX-II and C-REX will be forthcoming.

This has the previous daily run plans, i.e. prior to a cutoff date. The more recent run plans are found here:   RunPlanDaily

Daily Run Plan for PREX   (latest at bottom)

Date (2010)	Shift	---------- Activity (Responsible) ----------	--- Status ---
03/19	Day	pump down; Møller, Compton, septum install; Q2 repair Insert sieve. (Techs)	done
03/19	Swing	Beam restore (B-team)	done
03/20	Owl	Septum checkout (Michaels: Page when beam imminent & spectrometer ready) also: Initial look at low current cavity monitors (Ahmed: Page when beam imminent & spectrometer ready) Target alignment (Michaels) VDC checkout (Michaels) Quartz detectors checkout (McNulty, Wexler -- page when VDC tracks seen) GEM checkout (Camsonne -- page when VDC tracks seen, if left dipole is operating)	done All at 1-2 µA. Scattered energy ~ beam energy = 1.063 GeV. Quad settings: Right arm: Q1: dI/dP= 411.2474 Amps/GeV/c Q2: dI/dP= 436.2014 Amps/GeV/c Q3: dI/dP= 433.3897 Amps/GeV/c Left Arm: Q1: dI/dP= 419.8772 Amps/GeV/c Q2: dI/dP= 435.6273 Amps/GeV/c Q3: dI/dP= 434.9682 Amps/GeV/c "Usual" polarity
03/20	Day	Beam off & hall open 9:00 am Quads repair; Compton install; GEM install; signals debugging. Leave sieves in. (Techs)	done
03/20	Swing	Close up hall Benesch tuning (1/2 - 2 hours) Verify quad polarities (Camsonne) Cavity monitors basic function test (Ahmed) Low current cavity monitors setup (Musson, Ahmed)	done
3/21	Owl	Low current cavity monitors setup (Musson, Ahmed) Access for GEM installation (Camsonne)	done but GEMs not ready
3/21	Day	Spectrometer checkout: Quartz detectors checkout (McNulty, Wexler) Lumi checkout (Mercado) (2 µA on Ta) GEM checkout (Camsonne?) A line tuning (Benesch) Raster checkout Access: Low current cavities Target position Quartz Scintillator alignment LQ2	done
3/21	Swing	Low current cavity monitors setup (Michaels, Ahmed) Remove sieves Initial look at sieve out data Replace sieves	done
3/22	Owl	Pointing measurement (Riordan) Remove sieves Repeat pointing measurements with no sieves If done or unable to continue before 4 am page Luis Mercado to do lumi checks After 4 am page Dustin McNulty for detector work	done
3/22	Day	Optics (Liyanage) Sieve OUT. NB Current limit 2 uA!	done
3/22	Swing	Optics continued, sieve IN. NB Current limit 2 uA! (Shift Crew)	done
3/23	Owl	Quartz detectors resolution studies (KK, Dustin, John W) Lumi studies (Luis)	done
3/23	Day	Remove water target. (Target, Techs) Reconfigure Moller cryo. Beam studies ~ 2pm, study of helicity correlated position differences for spin flipper states. (Dalton, Rupesh, Reza)	water cell removed, rest not finished
3/23	Swing	Target pumpdown	done
3/24	Owl	Target pumpdown	done
3/24	Day	Target cooldown	done
3/24	Swing	Tune high current beam into Hall A	done
3/25	Owl	Commission lead target, 50 uA (Bob) Lumis and oversampling tests (KK, Luis, Paul)	in progress
3/25	Day	Access to fix left dipole	done
3/25	Swing	Parity Quality commissioning (Kent, Rupesh, Luis, Dustin) Beam monitor calibrations (Diancheng Wang, Xiaoyan Deng)	postponed
3/26	Owl	High Luminosity Detector Commissioning	in progress
3/26	Day	Moller Checkout	postponed
3/26	Swing	High Current on C12 (thick and thin)	partly done
3/27	Owl		no beam
3/27	Day		no beam
3/27	Swing	High-current on thick C12, adjust HV (Luis or Bob) Finish the commissioning of thick Pb target (Bob, Ahmed) Electronic Commissioning (KK, Luis, Paul, Jon et al)	done, high-current tests continue
3/28	Owl	Continue with the above, if necessary. High Luminosity Commissioning (Rupesh, Luis, Jon, Bob) BCM/BPM calibration (Rupesh) Establishing Parity Measurements, Charge feedback, blinding (Rupesh, Jon)	not finished
3/28	Day	Comparison Study of Optics Tunes (Seamus, Nilanga, Kiad) Sometime before Monday, submit the ATLIS plan for Dithering test (Rupesh)	done
3/28	Swing	Continue Optics if necessary. Continue High Luminosity Commissioning	done
3/29	Owl	Mini-production run (shift crew) Stop beam at 07:00 or whenever Ed Folts asks to.	done
3/29	Day	Open Hall A to set up Moller and Compton (Ed Folts, Sasha, Sirish, et.al.) Work on GEMs (Alex, Seamus, et.al.) MCC to do beam studies while Hall A open Detector linearity/LED tests (Luis) Setup WAC analysis (Mark, Mindy)	done
3/29	Swing	Moller magnet cooldown Optics and acceptance studies (Seamus, Ahmed, Nilanga)	done
3/30	Owl	Commission charge feedback (Mark) Current monitor calibration and pedestals determination (Mark) Quasi-production on Empty Target (owl shift crew)	done
3/30	Day	Access do work on Moller and Compton. Some GEM installation work. (Alex, Seamus, Kiad, Nilanga) Possible linearity/LED study. (Luis)	done, except linearity
3/30	Swing	First Commissioning of Moller -- Beam Checks (Sasha, Javier, Roman, Jay)	done
3/31	Owl	Scans of Septum and quad Q1 for tunes A and B. (Bob) Beam Studies of Helicity Correlations	done
3/31	Day	Beam Tuning (Jay Benesch)	done
3/31	Swing	Either or both of these: a) Moller Commissioning (Sasha, Javier, Roman, Jay) b) Tests of Dithering and other Beam-Related things (Kent, Rupesh)	Moller was done
4/1	Owl	If Kent's tests not done on Swing, continue here. (Kent, Rupesh) Beam and Septum scan with new tune (Seamus) Helicity-correlated beam studies (Shift crew)	done
4/1	Day	Beam Tuning (Jay)	done, successful
4/1	Swing	More beam tuning if necessary Moller Commissioning	done
Friday 2 April	Owl	Assuming the HRS tune has been frozen Check detector alignment A_T studies Q2 Measurements	partly done, needs more work
Friday 2 April	Day	Tuning Beam for Compton	done
Friday 2 April	Swing	20:00 Obtain sieve runs (optics mini-run plan), Q2 measurements (Bob)	done, but not Q2
Saturday 3 April	Owl	Obtain sieve runs on Ta (Nilanga mini-run plan) Put in Lead target at low current and do counting-mode runs (Rupesh, Ahmed) Integrate-mode with Lead at 2 or 3 uA (Luis, Jon)	done
Saturday 3 April	Day	Moller Commissioning (priority activity) Work on getting into production mode (Mark, Rupesh)	done, but not yet in prod.
Saturday 3 April	Swing	Moller commissioning	done
Sunday 4 April	Owl	Counting data on tune Y (right arm) super-thin carbon Change to tune B Integrate-mode with Lead at 2 or 3 uA (Luis, Jon)	done
Sunday 4 April	Day	Integrate-mode with thick carbon 50 uA Compton QWP1 calibration.	done
Sunday 4 April	Swing	General Compton commissioning and pseudo-production (empty target) parity data at 50 uA.	done
Monday 5 April	Owl	pseudo-production (empty target) parity data and Compton data at 50 uA.	done
Monday 5 April	Day	12:00 Jay to run optics test (~ 30 mins) Moller Spin Dance Set up vertical polarization and measure A_T	done
Monday 5 April	Swing	Continue to setup up vertical polarization Measurements of A_T on Pb and C12	done
Tuesday 6 April	Owl	Continue measurements of A_T on Pb and C12	partly done
Tuesday 6 April	Day	Possible horizontal scan: Tune B with sieve slit (Seamus) When ready: Relocate Quartz Detectors (Dustin, Jack)	postponed: vacuum problems
Tuesday 6 April	Swing	In restricted access. Any activities that require access. Shift canceled
Wednesday 7 April	Owl	Shift cancelled
Wednesday 7 April	Day	Shift cancelled Investigate target vacuum problem Move quartz detectors (Dustin, Jack)	Leak found at O-ring connection between target chamber and collimator box
Wednesday 7 April	Swing	Shift cancelled
Thursday 8 April	Owl	Shift cancelled
Thursday 8 April	Day	Shift cancelled	Target chamber open, found that the 4th foil in Optics target blown off
Thursday 8 April	Swing	Shift cancelled
Friday 9 April	Owl	Shift cancelled
Friday 9 April	Day	To be determined. When ready: Install GEMs
Friday 9 April	Swing	Cancelled
Saturday 10 April	Owl	Cancelled
Saturday 10 April	Day	Cancelled
Saturday 10 April	Swing	Cancelled
Sunday 11 April	Owl	Cancelled
Sunday 11 April	Day	Cancelled
Sunday 11 April	Swing	Cancelled
Monday 12 April	Owl	Cancelled
Monday 12 April	Day	Cancelled
Monday 12 April	Swing	Cancelled
Tuesday 13 April	Owl	Cancelled
Tuesday 13 April	Day	Cancelled
Tuesday 13 April	Swing	Cancelled	Tungsten collimator modified and installed. Target pump down started and initially successful.
Wednesday 14 April	Owl	Cancelled	Target pump down.
Wednesday 14 April	Day	Cancelled -- no shift workers (might need a TO) Target pump down and leak checking. When ready, begin target cooldown. (Dave Meekins and JP)	Done. Vacuum good. Target cold.
Wednesday 14 April	Swing	Beam restore in Hall A Harp Scan - Shifters Raster size scan (goal is 3x3mm on empty cell) - Shifters. Detector Alignment - Dustin Dithering run with Septum On/Off - Rupesh.
Thursday 15 April	Owl	Thick Carbon Integrating Mode Run - Rupesh. Thick Carbon Dithering Run - Rupesh + Luis. Take Access: Change to counting mode and put sieve in - Ahmed.
Thursday 15 April	Day	Beam Studies -- establishing good beam in Hall A and Compton (Jay and B team)
Thursday 15 April	Swing	Detector Alignment - Dustin. Pb Alignment - Bob. Take access and put sieve in - Seamus. Sieve Alignment - Seamus. Take Access to remove sieve (Seamus) + switch to integrating mode (Jon) - Page Guy and Bob. Heat load test (run up to 500C) - Bob + Guy. If possible, depending on heat load test: Relative Rate 12C/Pb Runs - Bob / Dustin. Start production (Rupesh, Luis, Kent, Krishna)
Friday 16 April	Owl	Production
Friday 16 April	Day	Production
Friday 16 April	Swing	Production @ 40uA Ramp up to 50uA (Guy + Bob)
Saturday 17 April	Owl	Production @ 50uA
Saturday 17 April	Day	Production @ 50uA Moller Checks + Measurement Starting 9am (Sasha)
Saturday 17 April	Swing	Moller till 7pm (Sasha). Compton (Jay Benesch + Megan). Production @ 50uA.
Sunday 18 April	Owl	Production @ 50uA
Sunday 18 April	Day + Swing	Production @ 50uA. Staring 3pm: Compton test (Jay Benesch + Megan). Page Dustin + Jon + Bob + Sasha. Q^2 Measurement (Bob) Call Compton Experts Access: Refill Moller Magnet. Check Compton HV. Remove S0. Go to counting mode (Dustin). Compton Stuff. Detector Mapping (Jon). Detector Alignment (Dustin). Q^2 Measurement (Bob). Relative Rate Measurement (Bob). Access to Return to Integrating Mode. Production @ 50uA
Monday 19 April	Owl	Production @ 50uA
Monday 19 April	Day	Production @ 50uA
Monday 19 April	Swing	Production
Tuesday 20 April	Owl	Production
Tuesday 20 April	Day	Production Beam studies from approx. 11 am to 2 pm Hall A Activities: -- Compton 1/4wave stepper (Abdurahim) -- Check R-HRS Q2 and switch to remote mode (Heidi) -- Adjust R-HRS A_T (Dustin) -- Take pedestal data (Jon) -- Check 4th GEM and possibly install 5th (Alex, Jon) -- Test motion of A_T detector R-HRS (Jon) -- Possible Compton shielding / HV check (Megan) -- Ramp Moller magnet, measure stray fields. (Sasha) -- Parasitic work on floor (Yi Qiang)
Tuesday 20 April	Swing	Tune up Compton Production
Wednesday 21 April	Owl	Production
Wednesday 21 April	Day	Production
Wednesday 21 April	Swing	Production
Thursday 22 April	Owl	Production
Thursday 22 April	Day	Beam studies. Transverse Phase Space Study in Wien. (Reza, Mark, Rupesh) At ~2 pm start Moller commissioning
Thursday 22 April	Swing	Finish Moller (10 hours) Resume Production Don't forget the beam recovery procedure
Friday 23 April	Owl	Production
Friday 23 April	Day	Q2 Studies (3 hrs) -- Dustin, Bob GEM studies are only parasitic.
Friday 23 April	Swing	Production
Saturday 24 April	Owl	Production on thick C12
Saturday 24 April	Day	Production on thick C12 At about 2 pm switch to 120 Hz, still C12 Run briefly on C12 at 120 Hz Switch to thick Pb target (120 Hz)
Saturday 24 April	Swing	Production on Pb at 120 Hz
Sunday 25 April	Owl	Production
Sunday 25 April	Day	Q2 measurements - Bob, Dustin Otherwise production	done
Sunday 25 April	Swing	Production
Monday 26 April	Owl	Production
Monday 26 April	Day	Wien flip	Wien flip postponed until Tues
Monday 26 April	Swing	Production
Tuesday 27 April	Owl	Production
Tuesday 27 April	Day	Beam Studies Wien Flip Checks of laser at polarized source (Kent and EGG) Adiabatic Damping Study (Yves Roblin)	Done
Tuesday 27 April	Swing	Compton Tune 4 hrs on Thick Carbon (RD=0, IT=500us) flip half-wave plate 4 hrs on Thick Carbon
Wednesday 28 April	Owl	Finish Swing Plan Yves Roblin Measurement (if possible) Run on Carbon (RD=0, IT=1535)
Wednesday 28 April	Day	Moller
Wednesday 28 April	Swing	Finish Moller Production
Thursday 29 April	Owl	Production
Thursday 29 April	Day	Production	Access to repair target leak
Thursday 29 April	Swing	Production	Could not close hall due to faulty fire suppression system
Friday 30 April	Owl	Production	Could not close hall due to faulty fire suppression system
Friday 30 April	Day	08:00 Beam Stops for Open House
Friday 30 April	Swing	No Beam Injector studies
Friday 30 April	Owl	No Beam Injector studies
Saturday 1 May	Day	Open House Detector work Compton work
Saturday 1 May	Swing	Restore Beam. Check Beam Properties. (shift) Pulsed Beam Test. (Mark, Luis)
Sunday 2 May	Owl	Continue with Above Tests Raster and Pb Target Tests (Bob)
Sunday 2 May	Day	Continue Above Tests if necessary Start Production Get cavities to work at high current. (Ahmed) (The check of cavities at low current is postponed.)
Sunday 2 May	Swing	Production
Monday 3 May	Owl	Production
Monday 3 May	Day	Hall B Pass change 3 -> 5 until ~1:00PM Compton vacuum, LHRS dipole UPS replacement during the down Bake compton chicane overnight during production, run beam straight through Return to PbD #2 production Large asymmetry run (Jon)	Baking started, HRS work completed by Heidi
Monday 3 May	Swing	Production
Tuesday 4 May	Owl	Production
Tuesday 4 May	Day	Work on switch for Pockels cell (start 9:00AM) Complete Compton beam line bake-out, leak check, cavity alignment	Pockels cell switch work complete Compton vacuum reopened
Tuesday 4 May	Swing	Production	Continued Compton realignment/laser polarization measurement
Wednesday 5 May	Owl	Production	Stopped work on Compton - still not complete Changed beam spot size to 200x200um
Wednesday 5 May	Day	12 hours Moller tests, start 9:00AM (Sasha, Jixie)
Wednesday 5 May	Swing	Finish Moller tests, 21:00 Raster clock tests 22:00-24:00 (KK, Bob, Jon) Production as per raster clock tests
Thursday 6 May	Owl	Production
Thursday 6 May	Day	Beam Studies (8 hours controlled access starting 08:15) Finish Compton cavity work (Sirish, Abdurahim) Start Compton pumping, replace leaky upstream valve? (John Heckman et al) Remove GEM(s)?? (Alex, Kiad) Compton Boron installation (Megan)	Continued compton cavity alignment Boron installed INFN GEMs removed to EEL, (additional UVA GEM installed?
Thursday 6 May	Swing	Raster clock tests Production	CHL trip
Friday 7 May	Owl	Raster clock tests (cont?) Production	Tests aborted due to network switch failure in the hall
Friday 7 May	Day	Production Wien flip, QE scan, spot move (nominally 9:00AM)	Wien flip, QE scan, spot move completed. Compton valve work continued until 2:00 Started detector alignment checks Q2 and establish low-current cavities (Dustin)
Friday 7 May	Swing	Tests by KK et al Production
Saturday 8 May	Owl	Production
Saturday 8 May	Day	Production 2:00PM - Turn off cavity baking 3:00PM - Leak check, turn on ion pumps 4:00PM - Routine Moller Measurement	Compton vacuum reestablished Replaced valve opens with sufficient vacuum levels
Saturday 8 May	Swing	Moller	Moller measurement gives 91% polarization
Sunday 9 May	Owl	Production
Sunday 9 May	Day	Compton ready? Production	Cavity locks at 3kW! Valve upstream of chicane will not open
Sunday 9 May	Swing	Production
Monday 10 May	Owl	Production	Left dipole down Compton valve stuck
Monday 10 May	Day	Fix left dipole Fix Compton valve Fix target vacuum	Left dipole down Compton valve fixed and tested Target vacuum bad
Monday 10 May	Swing	Standby Empty or C target oversampling runs if valves can be opened 1-arm production if target vacuum < 5E-5	Left dipole down Target vacuum bad
Tuesday 11 May	Owl	Standby Empty or C target oversampling runs if valves can be opened 1-arm production if target vacuum < 5E-5
Tuesday 11 May	Day	Wien flip Beam studies -- injector studies Raster setup Fix left dipole Fix target vacuum
Tuesday 11 May	Swing	Compton tune Oversampling tests	Left dipole down Right dipole NMR down Target vacuum bad
Wednesday 12 May	Owl	Production	Left dipole down Right dipole NMR down Target vacuum bad
Wednesday 12 May	Day	Repair left dipole PS Repair right dipole NMR Repair right Q3 bad bit	Target vacuum bad
Wednesday 12 May	Swing	Standby	Left dipole down Left Q3 controls problem Target vacuum bad
Thursday 13 May	Owl	Standby	Left dipole down Left Q3 controls problem Target vacuum bad
Thursday 13 May	Day	Repair left dipole PS Repair left Q3 controls Find and stop target vacuum leak Warm up target
Thursday 13 May	Swing	Warm up target
Friday 14 May	Owl	Pump down target
Friday 14 May	Day	Pump down target
Friday 14 May	Swing	Cool target Re-establish beam Raster tests	Target vacuum good Both spectrometers good
Saturday 15 May	Owl	Production
Saturday 15 May	Day	Access for left dipole regulation	Left dipole regulation failed Target vacuum increase, then decrease with added heating
Saturday 15 May	Swing	Access for left dipole regulation Re-establish beam Møller	Left dipole regulation bad Target vacuum varying, mostly < 1e5
Sunday 16 May	Owl	Møller	Left dipole regulation bad Target vacuum varying, mostly < 1e5
Sunday 16 May	Day	Access for left dipole regulation	Target vacuum varying, mostly < 1e5
Sunday 16 May	Swing	Production Background test (L PMTs on)	Left dipole regulation bad Target vacuum varying, mostly < 1e5
Monday 17 May	Owl	Production
Monday 17 May	Day	Controlled Access for Left Dipole fix Moller refilled	Left dipole working for now Suspect bad silicon-controlled rectifier (SCR) There are 12 needed and only 6 spares Looking for spares and will work during beam studies Tue.
Monday 17 May	Swing	Production with both arms!
Tuesday 18 May	Owl	Production (hopefully with both arms!)	No Left Dipole issues all night
Tuesday 18 May	Day	Beam Studies, beginning 9am (8hrs) Wien Flip Maintenance on the Left Dipole Power supply	Wien Flip completed before beam studies Beam studies completed Measurements performed on Left Dipole Power supply
Tuesday 18 May	Swing	Production Oversample tests (Rupesh)	Compton not done Oversample tests not done
Wednesday 19 May	Owl	Production Oversample tests	Oversample tests completed
Wednesday 19 May	Day	Compton Tuning (1-2hrs, start around 10am) Raster tests during 'target vacuum recovery' Production	Injector tuning did not help Compton rates Jay and Yan are asking for advice Compton tuning during beam studies tomorrow
Wednesday 19 May	Swing	Production Q2 and detector alignment (2-3hrs, around 8pm)	short Q2 measurement Target vacuum tripped valves closed -> no beam
Thursday 20 May	Owl	Production	No beam - target operator only
Thursday 20 May	Day	Beam Studies (start at 8:30am, afternoon for Compton tuning) Some measurements on left dipole power supply by Jack in Hall Production	Compton tuning needs to be rescheduled Jack did some work in hall
Thursday 20 May	Swing	Canceled	We lost the target vacuum. Will need to warm up target and replace O-ring after letting radiation subside. Plan to replace O-ring on Monday May 24.
Friday 21 May	Owl	Canceled
Friday 21 May	Day	Canceled
Friday 21 May	Swing	Canceled
Saturday 22 May	Owl	Canceled
Saturday 22 May	Day	Canceled
Saturday 22 May	Swing	Canceled
Sunday 23 May	Owl	Canceled
Sunday 23 May	Day	Canceled
Sunday 23 May	Swing	Canceled
Monday 24 May	Owl	Canceled
Monday 24 May	Day	Various tests Pedestal runs linearity studies detector time constant tests GEM studies Target repairs - replace o-ring with silicon one temporarily Keep target warm and pump down Leak check
Monday 24 May	Swing	Pedestal runs
Tuesday 25 May	Owl	Canceled
Tuesday 25 May	Day	Beam Studies (until between 10am and noon) Pedestal runs	Kalres O-ring installed ahead of schedule. Pumping down.
Tuesday 25 May	Swing	Pedestal runs
Wednesday 26 May	Owl	Canceled
Wednesday 26 May	Day	Accelerator Vacuum Group in Hall for Leak checks Switch box arrived for activate remotely the heating and cooling of thetarget	Found a leak, but pressure stable at 675 mtor Electrician will install the appropriate outlet; R. Michaels is working on the remote control.
Wednesday 26 May	Swing	Canceled
Thursday 27 May	Owl	Canceled
Thursday 27 May	Day	Accelerator Vacuum Group in Hall for Leak checks
Thursday 27 May	Swing	Canceled
Friday 28 May	Owl	Canceled
Friday 28 May	Day	Shift workers on Standby Accelerator Vacuum Group in Hall for Leak checks
Friday 28 May	Swing	Canceled
Saturday 29 May	Owl	Canceled
Saturday 29 May	Day	Canceled
Saturday 29 May	Swing	Canceled
Sunday 30 May	Owl	Canceled
Sunday 30 May	Day	Canceled
Sunday 30 May	Swing	Canceled
Monday 31 May	Owl	Canceled
Monday 31 May	Day	Canceled
Monday 31 May	Swing	Canceled
Tuesday 1 June	Owl	Canceled
Tuesday 1 June	Day	Canceled
Tuesday 1 June	Swing	Canceled
Wednesday 2 June	Owl	Canceled
Wednesday 2 June	Day	Canceled
Wednesday 2 June	Swing	canceled
Thursday 3 June	Owl	Canceled
Thursday 3 June	Day	Cooling down target (more likely to start on Swing) Day shift on standby.
Thursday 3 June	Swing	Swing shift workers are needed. PREX detector in counting mode resume beam in Compton chicane ( MCC ) harp scan for beam profile and beam position ( Shift crew - MCC ) raster check ( Shift crew ) Long down target recovery procedure ( Shift crew ) Alignment checks, Q2 ( Dustin Mc Nulty ). put sieve in take alignement data put sieve out Q2 measurement Ask for access to go to integrating mode ( Jon Wexler or Amhed Zafar ) and remove Sieve Restart Production Production
Friday 4 June	Owl	Production
Friday 4 June	Day	Production
Friday 4 June	Swing	Production
Saturday 5 June	Owl	Production
Saturday 5 June	Day	Production
Saturday 5 June	Swing	Production
Sunday 6 June	Owl	Production
Sunday 6 June	Day	Production
Sunday 6 June	Swing	Production