Difference between revisions of "20180612-Radiation-Mtg"
From PREX Wiki
(→Agenda / Minutes) |
Ciprian Gal (Talk | contribs) |
||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
Back to [[Main_Page|Main Page]] >> [[Radiation_Mtg]] | Back to [[Main_Page|Main Page]] >> [[Radiation_Mtg]] | ||
| − | [[20180605-Radiation-Mtg|previous meeting]] << >> [[ | + | [[20180605-Radiation-Mtg|previous meeting]] << >> [[20180626-Radiation-Mtg|following meeting]] |
| Line 12: | Line 12: | ||
== Agenda / Minutes == | == Agenda / Minutes == | ||
| − | # SAM sims: | + | # SAM sims: Radial Scan with PREX beamline [[File:20180612-Radiation-Mtg-TaoYe.pdf]] |
| − | + | #* CC: Pulling out by 6cm and thinning materials gets close to radiation goals - spherical end cap simulation results coming later today | |
| − | #* | + | #* KP: you should include positrons for the rate for both simulations. |
| + | #* KP: can you translate that number into a width? TY: will work on it. | ||
| + | #* DA: how low is the electronics noise on the SAMs to make use of the 4 THz rate? | ||
| + | #* DA: we should pay attention to the raster (correlation between position and angle) | ||
| + | # TOSCA sims: Adam [https://ace.phys.virginia.edu:80/HAPPEX/3513 haplog3513] | ||
| + | #* AZ: shielding that was installed for tritium was implemented in TOSCA (based on original model from Jay) | ||
| + | #* AZ: we were mostly concerned what happens when one quad is off | ||
| + | #* AZ: with no shielding the focusing is consistent with previous TOSCA models. | ||
| + | #* AZ: with shielding the deflection is is 0.2 cm compared to 2 cm without over 17 m. | ||
| + | #* KP: maybe redo starting with \pm 3 cm and do CREX beam with CREX field and PREX beam with PREX field. AZ: will have to talk to Jay about the field strength. | ||
| + | #* AZ: working on setup shielding, but still figuring out how Jay made the model. | ||
== Attendance == | == Attendance == | ||
| − | + | Kent P, Ciprian G, Victoria O, Adam Z, Cameron C, Tao Y, David A, | |
=== Excused: === | === Excused: === | ||
Latest revision as of 09:21, 25 June 2018
Back to Main Page >> Radiation_Mtg
previous meeting << >> following meeting
Logistic information
BlueJeans calling instructions: Toll-Free Number (U.S.& Canada): 888-240-2560 International toll number: 408-740-7256 PARTICIPANT CODE: https://bluejeans.com/190761523
Agenda / Minutes
- SAM sims: Radial Scan with PREX beamline File:20180612-Radiation-Mtg-TaoYe.pdf
- CC: Pulling out by 6cm and thinning materials gets close to radiation goals - spherical end cap simulation results coming later today
- KP: you should include positrons for the rate for both simulations.
- KP: can you translate that number into a width? TY: will work on it.
- DA: how low is the electronics noise on the SAMs to make use of the 4 THz rate?
- DA: we should pay attention to the raster (correlation between position and angle)
- TOSCA sims: Adam haplog3513
- AZ: shielding that was installed for tritium was implemented in TOSCA (based on original model from Jay)
- AZ: we were mostly concerned what happens when one quad is off
- AZ: with no shielding the focusing is consistent with previous TOSCA models.
- AZ: with shielding the deflection is is 0.2 cm compared to 2 cm without over 17 m.
- KP: maybe redo starting with \pm 3 cm and do CREX beam with CREX field and PREX beam with PREX field. AZ: will have to talk to Jay about the field strength.
- AZ: working on setup shielding, but still figuring out how Jay made the model.
Attendance
Kent P, Ciprian G, Victoria O, Adam Z, Cameron C, Tao Y, David A,
