Difference between revisions of "CREX Detailed High current plan"

From PREX Wiki
Jump to navigationJump to search
(Created page with "CREX version == Beamline instrumentation calibration == #<font color=blue> Check detector alignment and pulse height</font> (Done) #* 1uA c...")
 
 
(9 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
[[CREX_Detailed_High_current_plan|CREX version]]
+
[[Detailed_High_current_plan|PREX version]], [[CREX_Detailed_Calibration_plan|CREX Calibration Plan]], [[CREX_Detailed_Production_plan|CREX Production Plan]]
−
== Beamline instrumentation calibration ==
+
== Beamline instrumentation calibration - All copied from PREX, updated to CREX numbers ==
 
#<font color=blue> Check detector alignment and pulse height</font> (Done)
 
#<font color=blue> Check detector alignment and pulse height</font> (Done)
−
#* 1uA cavity lock  
+
#* 1uA Hall A Target BPM lock (with Cavities if required, probably not)
 
#* 0.2% Carbon
 
#* 0.2% Carbon
 
#* 20 nA, cavity locks on and cavities in low current mode
 
#* 20 nA, cavity locks on and cavities in low current mode
Line 14: Line 14:
 
#* verify compton rates
 
#* verify compton rates
 
#<font color=blue>  Ramp to SAM Shutter test </font>
 
#<font color=blue>  Ramp to SAM Shutter test </font>
−
## Insert Lead Target.  
+
##* Insert Lead Target.  
−
##*Raster 10x10.  
+
##* Raster 10x10.  
−
##*  20 nA.  (Atten 107, slit 15)
+
##*  20 nA.  ''(Atten 107, slit 15)''
 
##* Cav locks on  
 
##* Cav locks on  
 
##* spot++ verify not seeing edges
 
##* spot++ verify not seeing edges
−
##* Set raster ?x?  (to get (x.y) = 4x6 real)
+
##* Set raster ?x?  ''(to get (x.y) = 4x6 real)''
−
## go up in current 1uA  (5min)
+
## Go up in current 1uA  (5min)
 
##* All HV off in HRS hut
 
##* All HV off in HRS hut
−
##* Target lock (0.6mm, 0.4mm)
+
##* Target lock ''(0.6mm, 0.4mm)'' -> (-0.3, -0.5) is collimator hole center for CREX
 
##* Collimator water temp
 
##* Collimator water temp
−
##* beamline temperatures
+
##* Beamline temperatures
 
##* Ion chamber (stability)
 
##* Ion chamber (stability)
 
##* SAM yields
 
##* SAM yields
 
##* BCM and BPM yields, widths.
 
##* BCM and BPM yields, widths.
−
#<font color=blue> access to remove SAM shutters, detector to integrate mode.</font>  
+
#<font color=blue> Aaccess to remove SAM shutters, detector to integrate mode.</font>  
−
#<font color=blue> Ramp to hi current test. </font>
+
#<font color=blue> Ramp to High current test. </font>
−
##* cavity bpm back to high current mode
+
##* Cavity bpm back to high current mode
 
##* All HV off in HRS hut, except quartz
 
##* All HV off in HRS hut, except quartz
−
##* Target lock (0.6mm, 0.4mm)
+
##* Target lock ''(0.6mm, 0.4mm)''
−
## 5uA (review) (10min)
+
## 20uA (review) (10min)
−
##* Target lock, FFB (monitor bpm SAT)
+
##* Target lock, FFB (monitor bpm Saturation)
 
##* Collimator water temp
 
##* Collimator water temp
−
##* beamline temperatures
+
##* Beamline temperatures
 
##* Ion chamber (stability)
 
##* Ion chamber (stability)
 
##* SAM and DET yields and widths
 
##* SAM and DET yields and widths
 
##* BCM and BPM yields, widths.
 
##* BCM and BPM yields, widths.
−
## 20uA (review) (10min)
+
## 100uA (review) (10min)
 
##* Target lock, FFB (monitor bpm SAT)
 
##* Target lock, FFB (monitor bpm SAT)
 
##* Collimator water temp
 
##* Collimator water temp
Line 47: Line 47:
 
##* SAM and DET yields and widths
 
##* SAM and DET yields and widths
 
##* BCM and BPM yields, widths.
 
##* BCM and BPM yields, widths.
−
## 40-50A(1hr)
+
## 150A(1hr)
 
##* Target lock, FFB (monitor bpm SAT)
 
##* Target lock, FFB (monitor bpm SAT)
 
##* Aq feedback
 
##* Aq feedback
Line 55: Line 55:
 
##* SAM and DET yields and widths
 
##* SAM and DET yields and widths
 
##* BCM and BPM yields, widths.
 
##* BCM and BPM yields, widths.
−
#<font color=blue>Calibration scan </font>
+
#<font color=blue>Calibration scan, see [[Detailed_Calibration_plan|Calibration Plan]]</font>
−
##*FFB ON  
+
#* FFB ON  
−
##* to 40-50uA
+
#* To 150 uA
−
##* SAMs HVs set
+
#* SAMs HVs set
−
##* DETs HVs set
+
#* DETs HVs set
−
##* PITA scan at end to check det linearities later
+
#* PITA scan at end to check det linearities later
 
#<font color=blue>BMW </font>
 
#<font color=blue>BMW </font>
−
##*tune beam, slow lock on (ad FFB on?), exercise BMW, check no ion chamber trips, check pauses locks and FFB
+
#* Tune beam, slow lock on (ad FFB on?), exercise BMW, check no ion chamber trips, check pauses locks and FFB
−
##*low current 2-3uA, exercise BMW, check BPM signals, check no ion chamber issues
+
#* Low current 2-3uA, exercise BMW, check BPM signals, check no ion chamber issues
−
##*target in, low current 2-3uA,exercise BMW, check BPM signals, check no ion chamber issues
+
#* Target in, low current 2-3uA,exercise BMW, check BPM signals, check no ion chamber issues
−
##*"ready for high current"
+
#* "Ready for high current"

Latest revision as of 13:34, 8 December 2019

PREX version, CREX Calibration Plan, CREX Production Plan

Beamline instrumentation calibration - All copied from PREX, updated to CREX numbers

  1. Check detector alignment and pulse height (Done)
    • 1uA Hall A Target BPM lock (with Cavities if required, probably not)
    • 0.2% Carbon
    • 20 nA, cavity locks on and cavities in low current mode
    • VDC on.
    • Check rates, verify pulse height spectra and alignment
    • Modify DAQ to include GEMS. 10 minute run with GEMS.
  2. C-Hole target, verify spot (Done)
    • 20 nA, spot ++ verify raster size
    • harp scan 4e, verify intrinsic size at target
  3. High current - no target (Skip it tonight)
    • verify compton rates
  4. Ramp to SAM Shutter test
      • Insert Lead Target.
      • Raster 10x10.
      • 20 nA. (Atten 107, slit 15)
      • Cav locks on
      • spot++ verify not seeing edges
      • Set raster ?x? (to get (x.y) = 4x6 real)
    2. Go up in current 1uA (5min)
      • All HV off in HRS hut
      • Target lock (0.6mm, 0.4mm) -> (-0.3, -0.5) is collimator hole center for CREX
      • Collimator water temp
      • Beamline temperatures
      • Ion chamber (stability)
      • SAM yields
      • BCM and BPM yields, widths.
  5. Aaccess to remove SAM shutters, detector to integrate mode.
  6. Ramp to High current test.
      • Cavity bpm back to high current mode
      • All HV off in HRS hut, except quartz
      • Target lock (0.6mm, 0.4mm)
    2. 20uA (review) (10min)
      • Target lock, FFB (monitor bpm Saturation)
      • Collimator water temp
      • Beamline temperatures
      • Ion chamber (stability)
      • SAM and DET yields and widths
      • BCM and BPM yields, widths.
    3. 100uA (review) (10min)
      • Target lock, FFB (monitor bpm SAT)
      • Collimator water temp
      • beamline temperatures
      • Ion chamber (stability)
      • SAM and DET yields and widths
      • BCM and BPM yields, widths.
    4. 150A(1hr)
      • Target lock, FFB (monitor bpm SAT)
      • Aq feedback
      • Collimator water temp
      • beamline temperatures
      • Ion chamber (stability)
      • SAM and DET yields and widths
      • BCM and BPM yields, widths.
  7. Calibration scan, see Calibration Plan
    • FFB ON
    • To 150 uA
    • SAMs HVs set
    • DETs HVs set
    • PITA scan at end to check det linearities later
  8. BMW
    • Tune beam, slow lock on (ad FFB on?), exercise BMW, check no ion chamber trips, check pauses locks and FFB
    • Low current 2-3uA, exercise BMW, check BPM signals, check no ion chamber issues
    • Target in, low current 2-3uA,exercise BMW, check BPM signals, check no ion chamber issues
    • "Ready for high current"
Retrieved from "https://prex.jlab.org/wiki/index.php?title=CREX_Detailed_High_current_plan&oldid=9408"