Difference between revisions of "WAC Notes"

Revision as of 21:10, 8 August 2019

In the process of editing and updating this page. Please contact Juliette Mammei crowder@jlab.org with questions or suggestions.

PREX Main << Weekly Analysis Coordinator << Instructions

Weekly Analysis Coordinator Notes

Slug Summary Notes

Slug 0

Slug 1

Slug 2

Slug 3

IHWP: Out
Wien: Right
Current: 50 uA
- BCM noise in BCM an us begins to be a problem
HRSs: Both
- PREX 1 thick Quartz
BCM: an_ds
- Analysis in adaqfs disks is still an_ds3 normalized at this time

Slug 4

IHWP: Out
Wien: Right
Current: 50 uA
HRSs: Both
- PREX 1 thick Quartz
BCM: an_ds
- Analysis in adaqfs disks is an_ds3 normalized at this time

Slug 5

IHWP: Out
Wien: Right
Current: 70 uA
HRSs: Both
- PREX 1 thick Quartz
BCM: an_ds
- Analysis in adaqfs disks is an_ds3 normalized at this time

Slug 6

IHWP: Out
Wien: Right
Current: 50 uA
HRSs: Both
- PREX 1 thick Quartz
BCM: an_ds
- Analysis in adaqfs disks is an_ds3 normalized at this time

Slug 7

IHWP: Out
Wien: Right
Current: 50 uA
HRSs: Both
- PREX 1 thick Quartz
BCM: an_ds
- Analysis in adaqfs disks is an_ds3 normalized at this time

Slug 8

IHWP: In
Wien: Right
Current: 50 uA
- PQB commences
HRSs: Left arm only
- PREX 1 thick Quartz
BCM: an_ds
- This is when we switched to an_ds from an_ds3 (in the maps being used by adaqfs at this time)

Slug 9

IHWP: Out
Wien: Right
Current: 50 uA
HRSs: Left arm only
- PREX 1 thick Quartz
BCM: an_ds

Slug 10

IHWP: In
Wien: Right
Current: 50 uA
HRSs: Left arm only
- PREX 1 thick Quartz
BCM: an_ds
This was a particularly noisy beam motion slug. FFB was off most of the time

Slug 11

IHWP: Out
Wien: Right
Current: 50 uA
HRSs: Left arm only
- PREX 1 thick Quartz
BCM: an_ds
FFB has now been turned on perpetually, and beam motion is stable, but the BPMs are noisier

Slug 12

IHWP: IN
Wien: Right
Current: 70 uA
Total Good Runs: 9
Total Good Charge: 1.40C
HRSs: Both Arms
- PREX 1 thick Quartz in RHRS
RHRS Returns to usability
New PREX II Quartz in Left Arm Only at this time
analog BCMs started being noisy
Tried bpm4ec and returned back to bpm4e for regression
use bpm11X instead of bpm12X

Slug 13

IHWP: Out
Wien: Right
Current: 70uA-50uA
Total Good Runs: 15
Total Good Charge: 2.04C
- Started from 70uA and went down to 50uA because the collimator temperature started increasing
- Many of the runs were under suspicious category because we were not sure about the target performance during those runs
- Now we decided the runs in suspicious category were not hitting copper frame so turned into good runs
HRSs: Both Arms
- PREX 1 thick Quartz (RHRS) and 5mm thin quartz (LHRS)
Burp Cut has been started from this slug

Slug 14

IHWP: IN
Wien: Right
Current: 70 uA
Total Good Runs: 13
Total Good Charge: 2.42C
HRSs: Both arms
- PREX 1 thick Quartz (RHRS) and 5mm Quartz (LHRS)
For some of the runs LQ1 tripped, applied bad_evt_cut

Slug 15

IHWP: OUT
Wien: Right
Current: 70 uA
Total Good Runs: 7
Total Good Charge: 1.37C
HRSs: Both arms
- PREX 1 thick Quartz (RHRS) and 5mm Quartz (LHRS)
For some of the runs LQ1 tripped, applied bad_evt_cut
LQ1 tripped during some of the runs. Needed to apply bad_evt_cut

Slug 16

IHWP: IN
Wien: Right
Current: 70 uA
Total Good Runs: 8
Total Good Charge: 1.44C
HRSs: Both arms
- PREX 1 thick Quartz (RHRS) and 5mm Quartz (LHRS)
For some of the runs LQ1 tripped, applied bad_evt_cut

Slug 17

IHWP: OUT
Wien: Right
Current: 70 uA
Total Good Runs: 6
Total Good Charge: 1.16C
HRSs: Both arms
- PREX 1 thick Quartz (RHRS) and 5mm Quartz (LHRS)
For some of the runs LQ1 tripped, applied bad_evt_cut

Slug 18

IHWP: IN
Wien: Right
Current: 70 uA
Total Good Runs: 11
Total Good Charge: 1.65C
HRSs: Both arms
- PREX 1 thick Quartz (RHRS) and 5mm Quartz (LHRS)
For some of the runs LQ1 tripped, applied bad_evt_cut

Slug 19

IHWP: OUT
Wien: Right
Current: 70 uA
Total Good Runs: 6
Total Good Charge: 0.87C
HRSs: Both arms
- PREX 1 thick Quartz (RHRS) and 5mm Quartz (LHRS)
For some of the runs LQ1 tripped, applied bad_evt_cut

Slug 20

IHWP: OUT
Wien: Right
Current: 70 uA
Total Good Runs: 5
Total Good Charge: 0.88C
HRSs: Right arm only
- PREX 1 thick Quartz (RHRS) and 5mm Quartz (LHRS)
Note: During slug19 LQ1 completely failed to work starting run3718 and we decided to upgrade all the runs from 3718 to 3732 to slug20 even if the IHWP status didn't change

Slug 21

IHWP: IN
Wien: Right
Current: 70 uA
New PREX II Quartz in Right Arm also now
Total 1.7 C good charge

Slug 22

IHWP: OUT
Wien: Right
Current: 70 uA
Total 1.13 C good charge
Runs 3764-3769

Slug 23

IHWP: IN
Wien: Right
Current: 70 uA
Total 0.96 C good charge
Runs 3770-3774

Slug 24

IHWP: OUT
Wein: Right
Current: 70 uA
Total 1.40 C good charge
Runs 3776-3786

Slug 25

IHWP: IN
Wein: Right
Current: 70 uA, ramps down
Total 0.6 C good charge
Runs 3787, 3788, 3791

Slug 26

Run 3797 is wien flip from Right to Left (first flip)
IHWP: OUT
Wein: Left
Total 0.88 C good charge
Runs 3803-3810

Slug 27

IHWP: IN
Wein: Left
Total 1.65 C good charge
Runs 3811-3823
increased widths as target D9-208Pb-D10 degraded (through run 3821); improved with new target (run 3822)

Slug 28

IHWP: OUT
Wein: Left
Total 1.34 C good charge
Runs 3834-3840

Slug 29

IHWP: IN
Wein: Left
Total 1.85 C good charge
Runs 3841-3862

Slug 30

IHWP: OUT
Wein: Left
Total 1.27 C good charge
Starts run 3863-3883

Slug 31

LHRS only (RHRS ROC crashed)

@@ Line 279: / Line 279: @@
 * '''Total 1.65 C good charge'''
 * Runs 3811-3823
+* increased widths as target D9-208Pb-D10 degraded (through run 3821); improved with new target (run 3822)
 === [https://prex.jlab.org/wiki/index.php/WAC_Notes_August_4_2019 Slug 28] ===

Difference between revisions of "WAC Notes"

Revision as of 21:10, 8 August 2019

Weekly Analysis Coordinator Notes

Week 3 - Cameron

Week 4 - Devi

Week 5 - Victoria

Week 6 - Adam

Slug Summary Notes

Slug 0

Slug 1

Slug 2

Navigation menu

Search