TEDf-VQWK-Testing

Back to Main Page >> DAQ Documentation Portal >> DAQ Testing

Board Testing

We will log bad boards and upload plots and descriptions of problems to: https://misportal.jlab.org/mis/apps/peer/submit.cfm

• Run 1654 - testing a board to replace CH "vqwk1" "bad" board
  • Plots
  • It works, this board can be used - has label on top "MDBKG"
  • This board is then used to replace the board in CH "vqwk1" and Tao has taken data to establish pedestals
  • HAPLOG 3619 describes BPM 8 test with new ADC in CH crate
  • run 1233 and 1234 were used to test (run 1233 had address conflict, so ignore)
• Run 1655 - test ADC 26
  • Plots
  • It works
• Run 1656 - test ADC 20 - testing original CH "vqwk1" "bad" board (top 4 channels are bad, ch's 4-7).
  • Plots
  • Top 4 channels are bad, as seen in CH crate data
• Run 1657 - test ADC 15, the one with the strangely wired and tied on Op Amp
  • Plots
  • Works
• Run 1658 - test ADC 37 - ISU board that has recently had new channels go bad on it
  • Plots
  • Bad channels 2, 3, 4
  • Channels 2 and 4 are highly non-linear, basically flat lines offset from pedestal
  • Channel 3 works only in positive voltage range
  • No Japan error codes are reported
• Run 1659 - test ADC 32 - used wrong HW address, no ACC light blinking and many VQWK read errors on telnet session
• Run 1660-1662 - test ADC 32 - corrected HW address (needs to be 0x8400)
  • Plots for first 6 channels tested
  • Plots for intermediate test run to remove VQWK read errors
  • Plots for post-reboot run with no signals at all (also no Japan error codes)
  • So it looks like all 8 channels are bad, and halfway through the run something broke even more
    • At about event 11000 vqwk read error messages started streaming on the telnet session after I plugged ramp DAC into channel 5 (6th on the board)
    • I started a new run to clear read error messages, that didn't fix, so I rebooted, and after rebooting the data is clear - no signal/analog output from ADC channels
  • I removed the board and marked it as dead
  • Mark Taylor has since fixed it
    • Run 1742 - Plots
• Run 1663 - test ADC 33 - ISU backup board
  • Plots
  • All but channel 6 are bad
  • No error code - just bad channel responses
• Run 1664 - test ADC 31
  • Plots
  • There are ROC read errors for 1/3 events or so
  • All channels have crazy noise and no response to input voltage
  • Read errors get worse when plugging a signal into a channel
  • Some channels show differing response to input... characterizing problems will be a bit hard, so assume normal input stage problems? Or wiring to the later stages is bad across all channels?
• Run 1665 - test ADC 31
  • Plots
  • Same ADC, same issues, rebooting VME crate didn't help
  • All 8 channels are bad, but some appear to have effects on their neighbors?
• Run 1666 - test ADC 3 - a repaired board, previously tested in run 4642 in CH crate in November
  • Plots - old bad
  • Plots - new fixed, abridged plots (zoom x axis for ease of viewing)
  • Plots - new fixed
  • So Mark Taylor has fixed the board.
  • Here are plots comparing channel (indexed) 1, 2, and 3 old data with new
  • I tested it again, for good measure: Here
• Run 1668 - test ADC 6
  • Plots
  • All channels look good
• Run 1690 - test ADC 20
  • Plots
  • All channels look good - fixed by Mark Taylor
• Run 1691 - test ADC 37
  • Plots
  • All channels look good - fixed by Mark Taylor
• Run 1710 - test ADC 8
  • Plots
  • All channels look good - fixed by Mark Taylor
• Run 1713 - test ADC 33
  • Plots
  • All channels look good - fixed by Mark Taylor
• Run 1714 - test ADC 31
  • Plots
  • All channels look good - fixed by Mark Taylor

Status

Most spare boards have problems, but Mark Taylor can fix them

9 out of 72 spare channels are bad.

Catalog

• ADC 3
  • Fixed by Mark Taylor - 2/15/2019
• ADC 6
  • Determined to work - 2/15/2019
• ADC 8
  • No pre-fix test given
  • Mark Taylor has now fixed it - 3/14/2019
• ADC 15
  • Determined to work - 2/13/2019
• ADC 20
  • Determined not to work - 2/13/2019
  • Channels 4-7 (top 4) do not work
  • Signal ramps to -10 V for all events, regardless of containing a voltage signal or not
  • Mark Taylor has now fixed it - 3/1/2019
• ADC 26
  • Determined to work - 2/14/2019
• ADC 31
  • Determined not to work - 2/15/2019
  • There are ROC read errors for 1/3 events or so
  • All channels have randomly stepping noisy signal that rails into certain regions and no clear response to input voltage
  • ROC Read errors get worse when plugging a signal into a channel
  • Some channels show differing response to input... characterizing problems will be a bit hard, so assume normal input stage problems? Or wiring to the later stages is bad across all channels?
  • Mark Taylor has now fixed it - 3/14/2019
• ADC 32
  • Determined not to work - 2/14/2019
  • All 8 channels have interesting problems
  • It looks like regular bad amplifier in input stage problems
  • But, in the third run I took with this board it looks like the signal stopped being read by digital components entirely (run 1662, all signals == 0)
  • Mark Taylor has now fixed it - 3/19/2019
• ADC 33
  • Determined not to work - 2/15/2019
  • Regular bad channels
  • Channel 6 "works" but probably it would be best to go ahead and give it a standard replacement treatment too?
  • Mark Taylor has now fixed it - 3/14/2019
• ADC 37
  • Determined not to work - 2/14/2019
  • A few channels are bad - 2, 3, 4 (index, starts at 0 in software, starts at 1 on board face)
  • Mark Taylor has now fixed it - 3/1/2019
  • Pre-fix full plots of toggle-pair-asymmetry: Plots
  • Post-fix full plots of toggle-pair-asymmetry: Plots